nea4wd.org

by **Jeepster** » Mon Mar 16, 2009 12:04 pm

Any body got any feed back on Aftermarket Axle shafts? Such as, YUKON, USA CROME ALLOY, Superior, Gonna be upgrading and looking into buying the Yukon ones.

Anybody have any input on these?

:twisted:

by **rblank** » Mon Mar 16, 2009 12:39 pm

NEOW is probably where you'll get the most response about this, it has more "tech traffic" than this site.

But IIRC Alloy USA went out of business and was bought by another company. A few guys in my club are having problems getting the "Lifetime warranty" filled on thier busted shafts.

by **axle** » Mon Mar 16, 2009 1:59 pm

alloy USA info;
http://newenglandjeepz.org/forum/techni ... n-factory/

by **JayK** » Mon Mar 16, 2009 2:14 pm

Link to Rubicon Owners Forum about Alloy.

http://www.rubiconownersforum.com/phpbb3/viewtopic.php?f=22&t=63231&st=0&sk=t&sd=a&hilit=alloy

by **Paul** » Mon Mar 16, 2009 3:26 pm

Superior was always good but always on national-back order. Takes months to get. Moser does not honor their crap anymore. Might try Yukon or whatever other companies there are left out there.

tip: If they don't have your Superiors in stock, you will NEVER get them.

:paul:

by **Jeepster** » Mon Mar 16, 2009 4:18 pm

Have you heard anything at all about the Yukon Shafts?

by **smileyfish** » Mon Mar 16, 2009 4:19 pm

try localy, i had good luck here. he suports local stuff like the jeep rally, fall crawl and stuff.

http://www.mitchelldiff.com/

by **tammylynn** » Mon Mar 16, 2009 5:31 pm

smileyfish wrote:try localy, i had good luck here. he suports local stuff like the jeep rally, fall crawl and stuff.

http://www.mitchelldiff.com/

x2

He has donated to the DWE Show on a regular basis too.

by **Zaedock** » Mon Mar 16, 2009 6:36 pm

Jeepster wrote:Have you heard anything at all about the Yukon Shafts?

I like Yukon stuff. Their 4340 shafts seem to hold up well.

smileyfish wrote:try localy, i had good luck here. he suports local stuff like the jeep rally, fall crawl and stuff.

http://www.mitchelldiff.com/

I run Mitchell alloy shafts in my rear axle. Good quality.

by **Ryan** » Mon Mar 16, 2009 7:56 pm

I have Mitchell alloy front shafts....they look nice havent had a chance to flog them but i know mitchell has stood by other work they have done for me

by **BILLYjp2** » Mon Mar 16, 2009 10:09 pm

Ryan wrote:I have Mitchell alloy front shafts....they look nice havent had a chance to flog them but i know mitchell has stood by other work they have done for me

he gets his shafts from superior and cuts and splines them himself. Great guy easy to deal with. would gladly give him my business

by **Liza** » Tue Mar 17, 2009 7:33 am

Jeepster wrote:Have you heard anything at all about the Yukon Shafts?

We (Bay State Off Road) retail the Yukon shafts and haven't had any complaints or problems. I'd run them.

nea4wd.org

Front Axle Shafts for Dana 44

Front Axle Shafts for Dana 44

Who is online